Insert one end of trimmer lines into an eyelet and push line equal distance through trimmer head.Ĥ. Align arrows on top of knob with openings in eyelets.ģ. Cut one piece of line to recommended length 0.95-.105" - 20 feet.Ģ. Speed Feed® Universal Trimmer Head 400 LH/RH Trimmer Head (Part #99944200907) (SRM, 58V Trimmers, GT & non-ECHO Models):ġ. Hold drum and twist spool counter clockwise until peg clicks into hole. Hold spool and drum securely with one hand and pull each line to disengage from notches.Ĩ. Turn inner drive so that pegs in drive align with grooves in spool, and push spool into drum.ħ. Feed ends of line outward through eyelets in drum.Ħ. Place ends of lines into notches in spool, leaving 6 in. Wind both lines tightly and evenly (one on each side of barrier) in the direction of arrow on bottom of spool.Ĥ. trimmer lines into holes in spool, one on each side of barrier.ģ. Hold drum and turn spool clockwise until peg clicks and disappears from hole. SRM ECHOmatic Pro Trimmer Head (Part #21560031) (SRM Models):ġ. Slide drum and spool onto mounting shaft. Hold spool and drum securely with one hand, and pull each line to disengage from notches.ĩ. Place spool over drum, feed ends of the line outward through eyelets in drum.Ĩ. Place ends of the lines into notches in spool, leaving 6 in. Place index finger between the two strands, and wind line tighlt and evenly in the direction of the arrow. Use one piece of new nylon line and thread through the molded loop on the spool.ĥ. Hold drum firmly and turb knob clockwise. High Capacity Manual Trimmer Head ( Part #21560065) (SRM & PAS Models)Ģ. Place spring over mounting shaft and secure spool with knob. Slid drum and spool onto mounting shaft.ġ0. Hold spool and drum securely with one hand and pull each line to disengage from notches.ĩ. Place spool over drum, Feed ends of line outward through eyelets in drum.Ĩ. Place ends of lines into notches ins spool, leaving 6 in. Place index finger between the two strands and wind line tightly and evenly in the direction of arrow. Pull line tight and adjust so one end (6 in.) longer than the other.ĥ. Use one piece of new nylon line (20 ft.) long and thread through the modled loop on the spool. Pull spool and drum and pull drum off mounting shaft.Ĥ. Hold drum firmly and turn knob clockwise. Lay unit on ground with trimmer head assembly up.Ģ. Shut engine off, and disconnect spark plug wire. SRM Manual Dual Line Trimmer Head (Part #21560060) (SRM Models) (Discontinued):ġ. Cut remaining line loop to separate into two pieces. Hold drum securely and turn spool clockwise to wind line onto spool.ħ. Insert two ends of one 24-foot piece of 0.80-0.95" nylon trimmer line into holes on sides of drum.Ħ. Align arrows on spool with marks on drum.ĥ. Turn spool counter clockwise until locking pegs clicks into hole in spool.Ĥ. Align pegs on inner drive with grooves in spool and install spool onto drum. Clear any remaining line or debris from spool and drum.ģ. Push spool in and turn clockwise until locking peg clicks.Ģ.Pull spool out of drum. To view the part's catalog for this trimmer head, Click HereĮCHO U-Turn™ Trimmer Head (Part #99944200900) (SRM Models) (Discontinued):ġ. Push down on cover and twist cover clockwise until tab locks cover in place. Place button and cover on spool and align arrows. Install spool into housing over spring and be sure spool is installed so that the words "THIS SIDE UP" are visible.ħ. Place ends of line in the two notches molded in the spool with 5 to 6 in. Place index finger between the strands and wind line tightly and evenly in the direction of arrow on spool (clockwise).ĥ. Hold spool with words "THIS SIDE UP" facing you. Pull line tight and adjust so one end is 6 in. Use one piece of new nylon line (20 ft.) long and thread through the molded loop on the spool. Press tab in housing and twist cover counter clockwise to align arrows and remove cover and button.ģ. GT ECHOmatic Dual Line Head (Part #99944200240) (GT Models) (Discontinued):Ģ. To view the part's catalog for this trimmer head, please Click Hereįor additional information on this trimmer head, please Click Here To view the installation procedures for this trimmer head, please Click Here Trimmer line should advance approximately one inch. Push center button while pulling on line. Place button on spool and align cover pegs with housing holes push down on cover until cover locks in place.Ĩ. ![]() Install spool into housing over spring and be sure spool is installed so that the wordds "THIS SIDE UP" are visible.ħ. Hold spool with words "THIS SIDE UP" facing you and wind line tightly and evenly in the directionof arrow on spool (clockwise). long and thread end of line one inch through molded loop in spool in the direction of arrow on spool.ĥ. Push in housing tab and remove cover and button.ģ. Lay unit on the ground with head assembly up.Ģ. GT Single-Line Replacement Spool (Part #21560040) (GT Models) (Discontinued):ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |